Send us your distributor and we will remanufacture it for you. A perfect option for those who have time and want to save on costs. The remanufacturing process includes full inspection, disassembly, cleaning and degreasing. We then install a toothed timing belt, 3 German made top bearings, 1 German made lower bearing and a distributor pinion pin (part # 930 602 922 00). Clearances, timing and proper operation are then checked to ensure reliability. Please note: each distributor is remanufactured in Germany, so the lead times can vary.

This item may need to be sourced from Germany and would take 2-4 weeks to arrive. Once ordered it cannot be canceled. Please call to check stock or request expedited shipping.

This hose connects the front of the oil tank to the thermostat housing. We recommend replacing 2 qty. Clamps, part # 99951225202 when replacing this piece. Sold individually. 1 necessary per car. Please note: this will only fit the oil thermostat with part # 964 207 047 05 or 964 207 047 07 or 964 207 047 08.

This item may need to be sourced from Germany and would take 2-4 weeks to arrive. Once ordered it cannot be canceled. Please call to check stock or request expedited shipping.

Looking for a more cost-effective solution than ordering a new link? Let us recondition your original drop link. The reconditioning process includes full inspection, disassembly, degreasing and media blasting. Once fully prepared, we properly install new bushings, finish with a corrosion proof coating and include a new lock nut. Please note: each link is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your link we will notify you as soon as we can. Arrangements can be made for its return to you. Sold individually. 1 necessary per car.

This item may need to be sourced from Germany and would take 2-4 weeks to arrive. Once ordered it cannot be canceled. Please call to check sto...(choose a part on the right to read more)

Send us your OEM transmission mount bracket and we will restore it to better than new condition! Our service includes removal of the old mount, media blasting, proper installation of the new mount and protective seal coating. Our mount is remanufactured in europe by an OEM supplier using the finest materials. It is a 65 shore rubber hardness value which is the same as the what was standard on these cars. Simply order and send us your OEM bracket, we will take care of the rest. Approximate lead time is estimated between 3-6 weeks.

This item may need to be sourced from Germany and would take 2-4 weeks to arrive. Once ordered it cannot be canceled. Please call to check stock or request expedited shipping.

Looking for a more cost-effective solution than ordering a new link? Let us recondition your original drop link. The reconditioning process includes full inspection, disassembly, degreasing and media blasting. Once fully prepared, we properly install new bushings, finish with a corrosion proof coating and include a new lock nut. Please note: each link is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your link we will notify you as soon as we can. Arrangements can be made for its return to you. Sold individually. 1 necessary per car.

This item may need to be sourced from Germany and would take 2-4 weeks to arrive. Once ordered it cannot be canceled. Please call to check sto...(choose a part on the right to read more)

High quality, German made distributor repair kit that contains: 1 qty. Distributor timing belt 1 qty. Pin for distributor pinion 3 qty. German made bearings we also recommend a sealing ring, part # 91160210201

This item may need to be sourced from Germany and would take 2-4 weeks to arrive. Once ordered it cannot be canceled. Please call to check stock or request expedited shipping.

Genuine parts sourced from Porsche ag in Germany to ensure quality, reliability and precise fitment. Sold as a set. 1 necessary per car.

This item may need to be sourced from Germany and would take 2-4 weeks to arrive. Once ordered it cannot be canceled. Please call to check stock or request expedited shipping.

High quality, German made distributor repair kit that contains: 3 qty. German made bearings 1 qty. Distributor timing belt 1 qty. Pin for distributor pinion 1 qty. German made lower bearing we also recommend a sealing ring, part # 91160210201

This item may need to be sourced from Germany and would take 2-4 weeks to arrive. Once ordered it cannot be canceled. Please call to check stock or request expedited shipping.

Send us your OEM transmission mount bracket and we will restore it to better than new condition! Our service includes removal of the old mount, media blasting, proper installation of the new mount and protective seal coating. Our transmission mount is manufactured in europe by an OEM supplier using the finest materials (high carbon steel, 7075 t6 aluminum and 85 shore rubber - rs spec). Simply order and send us your OEM bracket, we will take care of the rest. Approximate lead time is estimated between 3-6 weeks.

This item may need to be sourced from Germany and would take 2-4 weeks to arrive. Once ordered it cannot be canceled. Please call to check stock or request expedited shipping.

Send us your distributor and we will remanufacture it for you. A perfect option for those who have time and want to save on costs. The remanufacturing process includes full inspection, disassembly, cleaning and degreasing. We then install a toothed timing belt (part # FVD 602 964 00) and a distributor pinion pin (part # 930 602 922 00). Clearances, timing and proper operation are then checked to ensure reliability. Please note: each distributor is remanufactured in Germany, so the lead times can vary.

This item may need to be sourced from Germany and would take 2-4 weeks to arrive. Once ordered it cannot be canceled. Please call to check stock or request expedited shipping.

We are committed to Porsche cars and are very happy to release an outer tie rod that consists of a monoball joint. Until now this was something that was really only available on racing models. Our tie rod will provide you with unequalled steering precision for street and track use. This component is manufactured in europe and contains the finest materials available, high carbon steel and 7075 t6 aluminum. Installation is seamless, this is a direct replacement for the OEM part number, 965 347 032 00. Sold individually. 2 needed per car. We also suggest replacing your inner tie rod, we have a uniball option, our part # 96434705805sp (qty. 1 is needed) and now is also a good time to replace your worn out inner tie...(choose a part on the right to read more)

The 11.8:1 compression will provide you with more acceleration than kits with 11.3:1 compression. For track use we recommend more aggressive cam (maximum valve lift (tdc) of 2.1 mm) . Piston's has very deep pockets for use with sport valves. These are 107 mm in size so are slip fit and do not require modifications. This kit is ideal for track use but can also be used on the street, it will add 35+ hp (depending on your additional modifications). Mahle pistons are forged for substantially higher and more uniform strength over pistons that are cast. Mahle cylinders are manufactured from st52 steel which has extremely high thermal resistance, they are nikasil coated which reduces wear and friction. We also have t...(choose a part on the right to read more)

This 9 inch front and 11 inch rear steel fender flare set is made in Germany, we offer a complete line of replacement bodywork to complement the entire Porsche model range. Sold individually. 1 necessary per car. Please note: for conversions, these flares will allow you to run 9 wide tires in the front and 11 wide in the rear. For the 964 / 965 models the torsion bar cut out must be filled. Due to variances in production at the factory, age, accident damage or rust, each part may require trimming and or adjustment for perfect fitment.

This item may need to be sourced from Germany and would take 2-4 weeks to arrive. Once ordered it cannot be canceled. Please call to check stock or request expedited shipping.

This is the top outer section of the cabrio top made in Germany with original sonnenland material. It is as close to the original as possible and is cut and trimmed to fit perfectly. Sonnenland material consists of 3 layers, dyed acrylic twill weave top layer, elastomeric rubber inner layer and polyester woven base layer. It provides increased strength against abrasion, increased fade resistance and the tighter woven layers are made for modern electric tops with stronger frames for the 911 and 964. Sonnenland high quality material was originally used by Porsche and other top German manufacturers. Made in Germany. This would replace original part # 911 561 051 012xw sold individually. 1 necessary per car. Only f...(choose a part on the right to read more)

Only for cars without pdcc ( active stabilizer ) bilstein b16 (pss10) suspension kits feature ride height adjustability with 10-stage manually adjustable dampers. Simply adjust compression and rebound settings, from comfort to competition, by rotating the setting number knob at the base of the shock. The front and rear progressive rate springs allow accurate adjustment of the vehicle ride height and center of gravity for the level of performance you seek. Ride height is adjustable from 1.0 to -1.5 20-40mm (front) & -1.0 to -1.5 20-40mm (rear - minimum 1 lowering). Bilstein b16 (pss10) suspension allows you to enjoy the kind of precise suspension tuning formerly available only on race cars. We recommend purchasi...(choose a part on the right to read more)

We suggest replacing the bolt and seal when installing this rail. Part #'s 96410517103 and 90012313130. Sold individually. 1 necessary per car.

This item may need to be sourced from Germany and would take 2-4 weeks to arrive. Once ordered it cannot be canceled. Please call to check stock or request expedited shipping.

This cassette box is complete and ready for installation. Great detail is taken to attempt to match the original weave size, color and polish. Whether you are adding carbon to the interior or matching existing pieces, this is high quality and is made in Germany so it is made to last, like the original. Sold individually. This is a replacement for the original part # 964 552 553 00 1db in carbon.

This item may need to be sourced from Germany and would take 2-4 weeks to arrive. Once ordered it cannot be canceled. Please call to check stock or request expedited shipping.

Bilstein b16 (pss10) suspension kits feature ride height adjustability with 10-stage manually adjustable dampers. Simply adjust compression and rebound settings, from comfort to competition, by rotating the setting number knob at the base of the shock. The front and rear progressive rate springs allow accurate adjustment of the vehicle ride height and center of gravity for the level of performance you seek. Ride height is adjustable from 1.0 to -1.5 20-40mm (front) & -1.0 to -1.5 20-40mm (rear - minimum 1 lowering). Bilstein b16 (pss10) suspension allows you to enjoy the kind of precise suspension tuning formerly available only on race cars. We recommend purchasing our lowering collar kit if you plan to run the...(choose a part on the right to read more)

This fits 964 c2 / c4 and rs models with engine codes # m64.01/02/03. This is an OEM part, sourced directly from Germany. Professional installation is required. Different manufacturing tolerances require an inspection of the free clearance of all parts! If you're not sure about what parts are right for your build, be sure to ask one of our parts specialists. Sold individually. 1 necessary per car.

This item may need to be sourced from Germany and would take 2-4 weeks to arrive. Once ordered it cannot be canceled. Please call to check stock or request expedited shipping.

Unsure about installing a replacement bushing? Send us your trailing arm and we will properly recondition and install the bushing for you. The reconditioning process includes full inspection of your trailing arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we properly install our rear clubsport trailing arm bushings, part # FVD3310212291. Our rear trailing arm bushings contain rubber inserts with a shore hardness value of 85, like what is used on rennsport models. They offer rs style handling characteristics, superior durability and are still forgiving enough for street use. When reconditioning the trailing arms, we als...(choose a part on the right to read more)

This fits 964 c2 / c4 and rs models with engine codes # m64.01/02/03. This is an OEM part, sourced directly from Germany. Professional installation is required. Different manufacturing tolerances require an inspection of the free clearance of all parts! If you're not sure about what parts are right for your build, be sure to ask one of our parts specialists. Sold individually. 1 necessary per car.

This item may need to be sourced from Germany and would take 2-4 weeks to arrive. Once ordered it cannot be canceled. Please call to check stock or request expedited shipping.

This fits 964 c2 / c4 and rs models with engine codes # m64.01/02/03. This is an OEM part, sourced directly from Germany. Professional installation is required. Different manufacturing tolerances require an inspection of the free clearance of all parts! If you're not sure about what parts are right for your build, be sure to ask one of our parts specialists. Sold individually. 1 necessary per car.

This item may need to be sourced from Germany and would take 2-4 weeks to arrive. Once ordered it cannot be canceled. Please call to check stock or request expedited shipping.

This fits 964 c2 / c4 and rs models with engine codes # m64.01/02/03. This is an OEM part, sourced directly from Germany. Professional installation is required. Different manufacturing tolerances require an inspection of the free clearance of all parts! If you're not sure about what parts are right for your build, be sure to ask one of our parts specialists. Sold individually. 1 necessary per car.

This item may need to be sourced from Germany and would take 2-4 weeks to arrive. Once ordered it cannot be canceled. Please call to check stock or request expedited shipping.

Unsure about installing a replacement bushing? Send us your trailing arm and we will properly recondition and install the bushing for you. The reconditioning process includes full inspection of your trailing arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we properly install our rear clubsport trailing arm bushings, part # FVD3310212291. Our rear trailing arm bushings contain rubber inserts with a shore hardness value of 85, like what is used on rennsport models. They offer rs style handling characteristics, superior durability and are still forgiving enough for street use. When reconditioning the trailing arms, we als...(choose a part on the right to read more)